Transport Canada issued a Ship Safety Bulletin to advise stakeholders of the potential consequences of:
- fuel change-over between residual fuel commonly known as Heavy Fuel Oil (HFO) and low sulphur fuel oil (LSFO); and
- the change-over requirements under MARPOL Annex VI and the Vessel Pollution and Dangerous Chemicals Regulations (the Regulations).
During combustion, sulphur oxides form from the sulphur in the vessel’s fuel. This is why we now control the sulphur content in fuel. For vessels using emission control technology, the controls use an equivalent sulphur dioxide to carbon dioxide ratio.
The Regulations set air emission standards, including sulphur content limits in marine fuel, within the North American Emission Control Area (NA-ECA). These Regulations can be accessed through the Laws of Canada website managed by the Department of Justice Canada. Transport Canada will enforce these Regulations as set out in the Policy on Compliance and Enforcement of the Canada Shipping Act, 2001– TP 13585.
Main engines, auxiliary engines and boilers switching over to low sulphur fuels will create many challenges to vessels operating in the NA-ECA. As of January 1st, 2015, all vessels operating in the NA-ECA must use fuel that does not exceed 0.10% sulphur content.
Most marine diesel engines and boilers are designed to operate on HFO. If the operator does not make sure fuel switching is done carefully during the transition from HFO to LSFO (with a sulphur content of 0.1%), this can put a vessel’s machinery at risk and jeopardize the safety of the vessel, passengers and crew. This is why MARPOL Annex VI, Regulation 14.6, requires vessels using separate fuel oils, to carry a written procedure for the fuel oil change-over.
Challenges
Since changing from high to low sulphur fuels during operations may lead to several challenges, the vessel operator must take into account the different operating temperatures of the two fuels. If they don’t do this, the vessel risks propulsion failure, black out, and/or damage to the machinery. HFO and LSFO have quite different operating temperatures. This means that a changeover operation not being done correctly may lead to a rapid fall or rise in temperature with increased chances of thermal shock to the equipment. Fuel systems also have to account for their difference in viscosity to avoid fuel pump failures, leaks, and clogged filters. The fact that HFO and LSFO are mixed in different ratios during the change-over procedure increases the risk of the fuels becoming incompatible; which may cause the engine to shut down.
MARPOL – Compliance
Vessel-owners and operators need to take a measured, well informed and well documented approach to fuel switching. They should post these required procedures in the engine control room and the wheel house for easy reference.
The procedure must outline the time required for the fuel oil service system to be fully flushed of all fuel oil exceeding the applicable sulphur content specified by MARPOL, or authorized by permit according to vessel documents, before entering the NA- ECA.
Information a ship operator must record in a ship’s official log book as prescribed by the vessel’s Administration includes:
- the volume of LSFO in each designated tank; and
- the date, time, and position of the vessel when any fuel oil change-over operation is:
- completed before entry into the ECA; or
- begun after leaving the ECA.
Assistance from Engine Manufacturer or Classification Society
Vessel owners may ask their engine manufacturer or classification society as appropriate to verify their change-over procedures and documents.
Hazardous Situations
Vessel owners/operators should do compliant fuel change-overs well in advance to avoid problems during the transiting passages, in proximity to shore or in narrow channels. Transport Canada has received reports of main engine shutdowns and blackouts, resulting in exposing the vessel to hazardous situations.
Owners/operators must also ensure vessels can access all available power of its engines it needs to maneuver in ice or in strong winds and currents. The engine manufacturer or classification society should be consulted as appropriate.
Other Considerations |
Transport Canada further notes and agrees with the following recommendations for vessel owners and operators from the US Coast Guard Marine Safety Alert 2-15 on the subject:
|
Inspection and Reporting
A vessel experiencing loss of power, or a significant reduction in power which may result in a dangerous occurrence when navigating in ice or in other difficult sea conditions are to report the occurrence to Transport Canada Marine Safety and Security, by way of the nearest Marine Communications and Traffic Services Centre (MCTS) via the ECAREG or RMIC on the East and West Coasts respectively. The owner/operator must also make arrangements with their flag Administration or the Recognized Organization acting on its behalf as appropriate, to inspect the vessel and report their findings to Transport Canada.
You may download the Ship Safety Bulletin by clicking here.
Source: Transport Canada
In the origin, I was straightforward with you propecia before and after has changed my existence. It has become much more fun, and now I have to run. Just as it is incredible to sit.